

If you have any questions before making a purchase chat with our online operators to get more information.
Ask An Expert
The ATEX Heating Mantle Controller is an explosion-proof temperature controller made for laboratory and process mantles used in hazardous (Ex) areas. It gives you steady, precise heat with simple controls and a clear digital display, so your solvents, reagents, and process media reach the right temperature and stay there. With Ex-rated components, antistatic design, and limited surface temperatures, it helps reduce ignition risks while improving accuracy and repeatability. Built for day-to-day use in Dubai, Sharjah, and Abu Dhabi, it supports common sensors (Pt100, Thermocouple K), PID control, soft start, alarms, and output to SSR or relay. Pair it with Atex heating mantles, drum/IBC heaters, and heating jackets for a complete, compliant setup. Available at Atex Hub with UAE-ready selection and after-sales support.
An Atex Heating Mantle Controller is a certified control unit that regulates the temperature of an electric mantle inside explosive atmospheres. Instead of guessing with manual dials, you set a precise setpoint, and the controller uses PID control to deliver just the right power. The result is smoother heating, fewer overshoots, and repeatable results. In the UAE—especially in Dubai, Sharjah, and Abu Dhabi—labs, pilot plants, and small production rooms use ATEX mantle controllers for solvent distillation, reflux, evaporation, and gentle heating of sensitive materials. Because the controller is Ex-rated and designed for Zone 1/2 (gas) and Zone 21/22 (dust), you can place it where it’s convenient, keep cables short, and keep operators confident.
Accurate heating of glassware mantles for distillation, reflux, and synthesis where stable temperature matters.
Pilot plant control to maintain tight temperature bands during solvent swap, concentration, or reaction holds.
Quality and repeatability, thanks to PID tuning, soft-start, and programmable ramp/soak options (model-dependent).
Safety-first operation with over-temperature cut-out, alarms, and limited surface temperatures that support Ex compliance.
UAE site integration with SSR, relay, or 4–20 mA outputs to link pumps, alarms, or building safety systems.
Oil & Gas / Marine labs: Sample prep, water cut checks, and solvent treatment under Ex rules.
Chemical & Paint labs: Controlled heating of resins, binders, solvents, and additives during R&D or QA.
Pharma & Food pilot lines: Gentle, uniform heat for actives, flavours, and process intermediates.
Education & Training in Ex areas: Safe, supervised heating where intrinsically safe or flameproof rules apply.
Service bays & skids: Portable control for mantles, trace heating pads, and small heating jackets on test stands.
Ex compliance made simple: Built for ATEX/IECEx zones with temperature-limited design and antistatic construction.
Precision & productivity: PID control, soft-start, and alarms help you hit the setpoint quickly and hold it steady.
Human-friendly: Big digits, clear buttons, robust connectors, and logical menus reduce operator errors.
UAE-fit support: Atex Hub helps match sensor type, output, and temperature class to your area classification.
Lower total cost: Fewer re-runs, tighter quality, and less downtime thanks to reliable control electronics.
| Technical Specifications | ATEX Heating Mantle Controller |
|---|---|
| Control Mode | PID / Auto-tune / Manual |
| Sensor Inputs | Pt100 (RTD) / Thermocouple K |
| Setpoint Range | 0–400 °C (model-dependent) |
| Control Output | SSR (logic) / Relay (NO/NC) |
| Analog Output | 4–20 mA (optional) |
| Display | High-visibility digital LED |
| Alarms | Over-temperature / Sensor fault |
| Supply Voltage | 230 V AC, single phase |
| Rated Load | Up to 10 A (relay) / SSR drive |
| Enclosure | Ex-rated, IP65 |
| Zone Suitability | Gas: Zone 1/2; Dust: Zone 21/22 (model-specific) |
| Temperature Class | T3/T4 (model-specific) |
| Earthing | External grounding point |
| Interfaces | Emergency stop input / Alarm relay (optional) |
| Cable Entries | Ex glands, M20/M25 (model-specific) |
| Mounting | Wall / Bench / Skid |
| Operating Temp | −10 to +50 °C |
| Documentation | Ex certificate, User manual, Declaration of Conformity |
| Warranty | 12 months |
ATEX Directive 2014/34/EU (EUR-Lex) – equipment for explosive atmospheres
IECEx Certified Equipment Scheme – international certification & certificate lookup
IEC 60079-0 – Explosive atmospheres—Equipment—General requirements
IEC 60079-11 – Intrinsically safe “i” (for IS variants and circuits)
IEC 60079-31 – Dust ignition protection by enclosure “t”
1) Can I use my existing Pt100 or K-type probe?
Yes. The controller accepts Pt100 and Type-K as standard; confirm lead type and length for best accuracy.
2) Is it safe to place in Zone 1 near my mantle?
Yes—choose the correct ATEX/IECEx marking, gas group, and temperature class for your area classification.
3) Will PID help with overshoot on solvents?
Yes. PID with auto-tune reduces overshoot and holds a stable setpoint for sensitive boiling points.
4) Can I drive a solid-state relay (SSR)?
Yes. The controller provides a logic SSR output; relay output is also available for direct switching (load-dependent).
5) Do I get alarms and an emergency stop input?
Yes. Over-temperature and sensor fault alarms are standard; E-stop and external alarm relay are available options.
6) Can it talk to my data logger or DCS?
Models with 4–20 mA or alarm relay can integrate easily. Ask Atex Hub for mapping and wiring guidance.
7) What support is available in the UAE?
Atex Hub provides model selection, wiring guidance, delivery, and after-sales support across Dubai, Sharjah, and Abu Dhabi.
The ATEX Heating Mantle Controller brings Ex safety, precision, and ease of use to your mantle heating tasks. With PID control, clear displays, and robust Ex hardware, it helps you heat faster, hold temperature better, and work safer—day after day—in Dubai, Sharjah, and Abu Dhabi. For sizing, zone selection, and documents, rely on Atex Hub.